站长百科 UBOOT编译--- make xxx_deconfig过程详解(一) 正文

UBOOT编译--- make xxx_deconfig过程详解(一)

2022-12-28,,,

make xxx_deconfig过程详解

1. 前言
2. 概述
3. build变量的定义
4. 目标%config的定义
4.1 依赖 scripts_basic
4.1.1 语句$(if $ (KBUILD_BUILTIN),$(builtin-target) $(lib-target) $(extra-y))
4.1.2 语句 $(if $ (KBUILD_MODULES),$(obj-m) $(modorder-target))*
4.1.3 $(subdir-ym)
4.1.4 $(always) 重点关注
4.1.4.1 src的定义
4.1.4.2 kbuild-dir的定义
4.1.4.3 kbuild-file的定义
4.1.4.4 又在Makefile.build中包含include scripts/Makefile.lib
4.2 依赖 outputmakefile
4.3 依赖 FORCE
4.4 规则 $ (Q)$(MAKE) $(build)=scripts/kconfig $@
5 总结

1. 前言

　UBOOT版本：uboot2018.03，开发板myimx8mmek240。

2. 概述

Ubootb编译第一步通常是执行make xxx_config，在编译指定顶层目录生成.config文件，这种方式要求厂商提供一个基础的xxx_config文件(通常来说开发者不会通过执行make menuconfig从零开始配置，这个工作过量太大了)。本文接下来的章节主要解析这条指令背后主要做了什么。我是用的开发板执行命令为：make myimx8mmek240-8mm-2g_defconfig

3. build变量的定义

在scripts/Kbuild.include 中定义：

###

# Shorthand for $(Q)$(MAKE) -f scripts/Makefile.build obj=

# Usage:

# $(Q)$(MAKE) $(build)=dir

build := -f $(srctree)/scripts/Makefile.build obj

4. 目标%config的定义

在顶层Makefile中定义：

# We need some generic definitions (do not try to remake the file).

scripts/Kbuild.include: ;

include scripts/Kbuild.include            //注意这个引用

......

config: scripts_basic outputmakefile FORCE

	$(Q)$(MAKE) $(build)=scripts/kconfig $@

%config: scripts_basic outputmakefile FORCE

	$(Q)$(MAKE) $(build)=scripts/kconfig $@

4.1 依赖 scripts_basic

（参考：linux内核Makefile中的变量build— 过渡篇（五））

# 顶层Makefile

# Basic helpers built in scripts/

PHONY += scripts_basic

scripts_basic:

	$(Q)$(MAKE) $(build)=scripts/basic

	$(Q)rm -f .tmp_quiet_recordmcount

展开变量build

# 顶层Makefile

# Basic helpers built in scripts/

PHONY += scripts_basic

scripts_basic:

	$(Q)$(MAKE) -f $(srctree)/scripts/Makefile.build obj=scripts/basic

	$(Q)rm -f .tmp_quiet_recordmcount

　make -f $(srctree)/scripts/Makefile.build obj=scripts/basic的解析如下：

这是一种不指定目标的情况，由于未指定目标，这时会使用Makefile.build中的默认目标__build。然后更进一步，会使用$(obj)/Makefile(scripts/basic/Makefile)中定义的变量来进行目标匹配。

__build在Makefile.build中的构建规则为：

__build: $(if $(KBUILD_BUILTIN),$(builtin-target) $(lib-target) $(extra-y)) \

	 $(if $(KBUILD_MODULES),$(obj-m) $(modorder-target)) \

	 $(subdir-ym) $(always)

	@:

4.1.1 语句$(if $ (KBUILD_BUILTIN),$(builtin-target) $(lib-target) $(extra-y))

在顶层Makefile中，KBUILD_BUILTIN的定义如下：

# note：顶层Makefile

  KBUILD_BUILTIN := 1

  export KBUILD_MODULES KBUILD_BUILTIN

该语句展开为：

$(builtin-target) $(lib-target) $(extra-y)

（1）lib-target

# note：顶层Makefile

ifneq ($(strip $(lib-y) $(lib-m) $(lib-)),)

	lib-target := $(obj)/lib.a

endif

在此语句之前obj-y := ;obj-m := ;obj-未定义。因此lib-target为空。

（2）builtin-target ​​​​​​​

# note：顶层Makefile

ifneq ($(strip $(obj-y) $(obj-m) $(obj-) $(subdir-m) $(lib-target)),)

	builtin-target := $(obj)/built-in.o

endif

在此语句之前obj-y := ; obj-m := ;obj-未定义 ; subdir-m := ;并且在所包含的文件中也没有给这些变量增加值。lib-target 为空。因此builtin-target为空。

（3）extra-y未定义
综上：语句$(if $ (KBUILD_BUILTIN),$(builtin-target) $(lib-target) $(extra-y))为空。

4.1.2 语句 $(if $ (KBUILD_MODULES),$(obj-m) $(modorder-target))*

在顶层Makefile中，KBUILD_BUILTIN的定义如下：

# note：顶层Makefile

KBUILD_MODULES :=

综上：语句$(if $ (KBUILD_MODULES),$(obj-m) $(modorder-target))为空。

4.1.3 $(subdir-ym)

在scripts/Makefile.lib中，subdir-ym的定义如下：

# note：scripts/Makefile.lib

# Subdirectories we need to descend into

subdir-ym	:= $(sort $(subdir-y) $(subdir-m))

......

subdir-ym	:= $(addprefix $(obj)/,$(subdir-ym))

subdir-y与subdir-m都为空。
综上：语句$(subdir-ym)为空。

4.1.4 $(always) 重点关注

在scripts/Makefile.build有如下定义

# note：scripts/Makefile.build

# The filename Kbuild has precedence over Makefile

kbuild-dir := $(if $(filter /%,$(src)),$(src),$(srctree)/$(src))

kbuild-file := $(if $(wildcard $(kbuild-dir)/Kbuild),$(kbuild-dir)/Kbuild,$(kbuild-dir)/Makefile)

include $(kbuild-file)

4.1.4.1 src的定义

在scripts/Makefile.build有如下定义

# note：scripts/Makefile.build

# Modified for U-Boot

prefix := tpl

src := $(patsubst $(prefix)/%,%,$(obj))

ifeq ($(obj),$(src))

prefix := spl

src := $(patsubst $(prefix)/%,%,$(obj))

ifeq ($(obj),$(src))

prefix := .

endif

endif

在命令make -f ./scripts/Makefile.build obj=scripts/basic我们传入了obj=scripts/basic
所以src = obj = scripts/basic, prefix := .

4.1.4.2 kbuild-dir的定义

在scripts/Makefile.build有如下定义

kbuild-dir := $(if $(filter /%,$(src)),$(src),$(srctree)/$(src))

所以 kbuild-dir = ./scripts/basic

4.1.4.3 kbuild-file的定义

在scripts/Makefile.build有如下定义

kbuild-file := $(if $(wildcard $(kbuild-dir)/Kbuild),$(kbuild-dir)/Kbuild,$(kbuild-dir)/Makefile)

所以kbuild-file = ./scripts/basic/Makefile

所以include $(kbuild-file)即为include ./scripts/basic/Makefile

在./scripts/basic/Makefile中：

# note：scripts/basic/Makefile

hostprogs-y	:= fixdep

always		:= $(hostprogs-y)

# fixdep is needed to compile other host programs

$(addprefix $(obj)/,$(filter-out fixdep,$(always))): $(obj)/fixdep

所以always = fixdep

4.1.4.4 又在Makefile.build中包含include scripts/Makefile.lib

而在scripts/Makefile.lib中

# note：scripts/Makefile.lib

always        := $(addprefix $(obj)/,$(always))

所以最终 always = scripts/basic/fixdep 。

故__build 展开如下：

__build: scripts/basic/fixdep

@:

1. 在Makefile.build中有如下定义：

# note：scripts/Makefile.build

ifneq ($(hostprogs-y)$(hostprogs-m),)

      include scripts/Makefile.host

endif

在./scripts/basic/Makefile中hostprogs-y = fixdep, 所以scripts/Makefile.host被包含进Makefile.build;

在scripts/Makefile.host中

# note：scripts/Makefile.host

__hostprogs := $(sort $(hostprogs-y) $(hostprogs-m))

hostprogs-m为空，所以__hostprogs = fixdep。

在scripts/Makefile.host中

# note：scripts/Makefile.host

# C code

# Executables compiled from a single .c file

host-csingle	:= $(foreach m,$(__hostprogs), \

			$(if $($(m)-objs)$($(m)-cxxobjs)$($(m)-sharedobjs),,$(m)))

......

host-csingle	:= $(addprefix $(obj)/,$(host-csingle))

因为fixdep-objs与fixdep-cxxobjs都不存在，所以host-csingle = fixdep； 又 host-csingle := $ (addprefix $ (obj)/,$(host-csingle))，所以host-csingle = scripts/basic/fixdep。

host-csingle规则如下：

# note：scripts/Makefile.host

$(host-csingle): $(obj)/%: $(src)/%.c FORCE

	$(call if_changed_dep,host-csingle)

等价于：

scripts/basic/fixdep:scripts/basic/fixdep.c FORCE

  $(call if_changed_dep,host-csingle)

2. if_changed_dep在scripts/Kbuild.include中定义

# note：scripts/Kbuild.include

# Execute the command and also postprocess generated .d dependencies file.

if_changed_dep = $(if $(strip $(any-prereq) $(arg-check) ),                  \

	@set -e;                                                             \

	$(echo-cmd) $(cmd_$(1));                                             \

	scripts/basic/fixdep $(depfile) $@ '$(make-cmd)' > $(dot-target).tmp;\

	rm -f $(depfile);                                                    \

	mv -f $(dot-target).tmp $(dot-target).cmd)

2.1 $(strip $(any-prereq) $(arg-check) )
(1) any-prereq在scripts/Kbuild.include中定义

# note：scripts/Kbuild.include

 any-prereq = $(filter-out $(PHONY),$?) $(filter-out $(PHONY) $(wildcard $^),$^)

$ ? 表示所有比目标还要新的依赖文件;$ ^ 表示所有的依赖文件，$(filter-out $ (PHONY), $?)就是过滤到比目标还要新的依赖文件中的伪目标，即为 scripts/basic/fixdep.c， $ (filter-out $ (PHONY) $ (wildcard $ ^ ), $^)表示过滤掉所有的依赖文件中的伪目标与存在的依赖文件，这里为空，所以any-prereq = scripts/basic/fixdep.c。

(2) arg-check在scripts/Kbuild.include中定义：

# note：scripts/Kbuild.include

ifneq ($(KBUILD_NOCMDDEP),1)

    arg-check = $(strip $(filter-out $(cmd_$(1)), $(cmd_$@)) \

     $(filter-out $(cmd_$@),   $(cmd_$(1))) )

else

    arg-check = $(if $(strip $(cmd_$@)),,1)

endif

KBUILD_NOCMDDEP是在make命令行中定义，我们并没有定义，所以：

arg-check = $(strip $(filter-out $(cmd_$(1)), $(cmd_$@)) $(filter-out $(cmd_$@), $(cmd_$(1))) )

<1> $ (filter-out $ (cmd_ $ (1)), $ (cmd_ $@)) 表示过滤掉 $(cmd_ $@)中符合 $(cmd_ $(1))的项。 $(1)表示if_changed_dep函数的第一个参数host-csingle， $@表示目标文件scripts/basic/fixdep。
<2> cmd_scripts/basic/fixdep并没有定义，所以 $(filter-out $(cmd_ $(1)), $(cmd_ $@))为空；
<3> cmd_host-csingle 在Makefile.host中定义：

cmd_host-csingle    = $(HOSTCC) $(hostc_flags) -o $@ $<  $(HOST_LOADLIBES) $(HOSTLOADLIBES_$(@F))

所以arg-check = $ (filter-out $ (cmd_$ @), $ (cmd_$ (1))) = $ (HOSTCC) $ (hostc_flags) -o $@ $< $(HOST_LOADLIBES) $(HOSTLOADLIBES_ $(@F))

$(any-prereq) $(arg-check)都为非空，所以：

if_changed_dep = @set -e;   \ /如果任何语句的执行结果不是true则应该退出

	$(echo-cmd) $(cmd_$(1));                                             \

	scripts/basic/fixdep $(depfile) $@ '$(make-cmd)' > $(dot-target).tmp;\

	rm -f $(depfile);                                                    \

	mv -f $(dot-target).tmp $(dot-target).cmd)

2.2 $(echo-cmd) $(cmd_ $ (1))等价于$(echo-cmd) $(cmd_host-csingle)

echo-cmd = $(if $( $(quiet)cmd_$(1)),echo '  $(call escsq, $( $(quiet)cmd_ $(1))) $(echo-why)';）

quiet=quiet_，在顶层Makefile分析过(当然如果你想看到更详细的打印，您可以通过传入V值，来改变)， $(cmd_host-csingle)上面分析过，存在，所以：

echo-cmd = echo '  $(call escsq,$(cmd_host-csingle))$(echo-why)';

在scripts/Kbuild.include中：

# Escape single quote for use in echo statements

escsq = $(subst $(squote),'\$(squote)',$1)

ifeq ($(KBUILD_VERBOSE),2)

why =                                                                        \

    $(if $(filter $@, $(PHONY)),- due to target is PHONY,                    \

        $(if $(wildcard $@),                                                 \

            $(if $(strip $(any-prereq)),- due to: $(any-prereq),             \

                $(if $(arg-check),                                           \

                    $(if $(cmd_$@),- due to command line change,             \

                        $(if $(filter $@, $(targets)),                       \

                            - due to missing .cmd file,                      \

                            - due to $(notdir $@) not in $$(targets)         \

                         )                                                   \

                     )                                                       \

                 )                                                           \

             ),                                                              \

             - due to target missing                                         \

         )                                                                   \

     )

echo-why = $(call escsq, $(strip $(why)))

endif

KBUILD_VERBOSE一般我们会采用默认值0(需要调试编译除外)，所以 echo-why 为空。

quiet_cmd_host-csingle 	= HOSTCC  $@ //用来打印

cmd_host-csingle =  '$(HOSTCC) $(hostc_flags) -o $@ $<  $(HOST_LOADLIBES) $(HOSTLOADLIBES_$(@F))'

$(HOSTCC)为cc，此处不再深入解释，hostc_flags在Makefile.host中定义：

#####

# Handle options to gcc. Support building with separate output directory

_hostc_flags   = $(HOSTCFLAGS)   $(HOST_EXTRACFLAGS)   \

            $(HOSTCFLAGS_$(basetarget).o) //-Wall -Wstrict-prototypes -O2 -fomit-frame-pointer

_hostcxx_flags = $(HOSTCXXFLAGS) $(HOST_EXTRACXXFLAGS) \

                 $(HOSTCXXFLAGS_$(basetarget).o)

ifeq ($(KBUILD_SRC),) //KBUILD_SRC在make命令行定义，此处未定义

__hostc_flags	= $(_hostc_flags)

__hostcxx_flags	= $(_hostcxx_flags)

else

__hostc_flags	= -I$(obj) $(call flags,_hostc_flags)

__hostcxx_flags	= -I$(obj) $(call flags,_hostcxx_flags)

endif

hostc_flags    = -Wp,-MD,$(depfile) $(__hostc_flags)

在scripts/Kbuild.include中：

comma   := ,

dot-target = $(dir $@).$(notdir $@)               //scripts/basic/.fixdep

depfile = $(subst $(comma),_,$(dot-target).d)     //scripts/basic/.fixdep.d

hostc_flags   =  -Wp,-MD,scripts/basic/.fixdep.d -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer

综上
cmd_host-csingle = cc -Wp,-MD,scripts/basic/.fixdep.d -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -o scripts/basic/fixdep scripts/basic/fixdep.c

所以echo-cmd 的作用是打印quiet_cmd_host-csingle（HOSTCC $ @ ）或者cmd_host-csingle（根据顶层MakefileV值决定），$ (cmd_$(1))即为执行cmd_host-csingle生成fixdep同时生成fixdep的依赖文件.fixdep.d

（2.3） scripts/basic/fixdep $(depfile) $@ ’ $(make-cmd)’ > $(dot-target).tmp
等价于：scripts/basic/fixdep scripts/basic/.fixdep.d scripts/basic/fixdep ‘cc -Wp,-MD,scripts/basic/.fixdep.d -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -o scripts/basic/fixdep scripts/basic/fixdep.c’ > scripts/basic/.fixdep.tmp

（2.4） rm -f $(depfile)
删除scripts/basic/.fixdep.d

（2.5） mv -f $(dot-target).tmp $(dot-target).cmd)
将scripts/basic/.fixdep.tmp重命名为scripts/basic/.fixdep.cmd

总结：生成scripts/basic/fixdep的过程中会先打印cc -Wp,-MD,scripts/basic/.fixdep.d -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -o scripts/basic/fixdep scripts/basic/fixdep.c同时执行该语句生成fixdep，再用fixdep生成.fixdep.cmd

4.2 依赖 outputmakefile

# 顶层Makefile

# outputmakefile generates a Makefile in the output directory, if using a

# separate output directory. This allows convenient use of make in the

# output directory.

outputmakefile:

ifneq ($(KBUILD_SRC),)

	$(Q)ln -fsn $(srctree) source

	$(Q)$(CONFIG_SHELL) $(srctree)/scripts/mkmakefile \

	    $(srctree) $(objtree) $(VERSION) $(PATCHLEVEL)

endif

上面批注已经说的很清楚了，outputmakefile 在输出目录中生成一个 Makefile，如果使用单独的输出目录。 这允许在输出目录中方便地使用 make。当KBUILD_SRC不为空时，才会编译到这里。

4.3 依赖 FORCE

# 顶层Makefile

PHONY += FORCE

FORCE:

实际上它是一个伪目标，从上面看到，FORCE 既没有依赖的规则，其底下也没有可执行的命令。如果一个规则没有命令或者依赖，而且它的目标不是一个存在的文件名，在执行此规则时，目标总会被认为是最新的。也就是说，这个规则一旦被执行，make 就认为它所表示的目标已经被更新过。当将这样的目标(FORCE)作为一个规则的依赖时(如上)，由于依赖总被认为是被更新过的，所以作为依赖所在的规则定义的命令总会被执行。

4.4 规则 $ (Q)$(MAKE) $(build)=scripts/kconfig $@

等价于：make -f $(srctree)/scripts/Makefile.build obj=scripts/kconfig myimx8mmek240-8mm-2g_defconfig

在scripts/kconfig/Makefile中(至于为什么会引用scripts/kconfig/Makefile，参见4.1小节)

# note：scripts/kconfig/Makefile

ifdef KBUILD_KCONFIG

Kconfig := $(KBUILD_KCONFIG)

else

Kconfig := Kconfig

endif

%_defconfig: $(obj)/conf

	$(Q)$< $(silent) --defconfig=arch/$(SRCARCH)/configs/$@ $(Kconfig) //$< = $(obj)/conf

# Added for U-Boot (backward compatibility)

%_config: %_defconfig

	@:

编译的流程为：
（1）先编译scripts/kconfig/conf可执行文件；
（2）再执行scripts/kconfig/conf --defconfig=arch/…/configs/myimx8mmek240-8mm-2g_defconfig Kconfig语句

编译打印如下

make -f ./scripts/Makefile.build obj=scripts/kconfig myimx8mmek240-8mm-2g_defconfig

  cc -Wp,-MD,scripts/kconfig/.conf.o.d -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer    -I/usr/include/ncursesw -DCURSES_LOC="<curses.h>"  -DNCURSES_WIDECHAR=1 -DLOCALE   -c -o scripts/kconfig/conf.o scripts/kconfig/conf.c

  cat scripts/kconfig/zconf.tab.c_shipped > scripts/kconfig/zconf.tab.c

  cat scripts/kconfig/zconf.lex.c_shipped > scripts/kconfig/zconf.lex.c

  cat scripts/kconfig/zconf.hash.c_shipped > scripts/kconfig/zconf.hash.c

  cc -Wp,-MD,scripts/kconfig/.zconf.tab.o.d -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer    -I/usr/include/ncursesw -DCURSES_LOC="<curses.h>"  -DNCURSES_WIDECHAR=1 -DLOCALE  -Iscripts/kconfig -c -o scripts/kconfig/zconf.tab.o scripts/kconfig/zconf.tab.c

  cc  -o scripts/kconfig/conf scripts/kconfig/conf.o scripts/kconfig/zconf.tab.o

scripts/kconfig/conf  --defconfig=arch/../configs/myimx8mmek240-8mm-2g_defconfig Kconfig

#

# configuration written to .config

#

5 总结

经过前面的分析可知：当执行make xxx_deconfig时，最终会执行以下两个语句：
（1）make -f $(srctree)/scripts/Makefile.build obj=scripts/basic
（2）make -f ./scripts/Makefile.build obj=scripts/kconfig xxx_deconfig

UBOOT编译--- make xxx_deconfig过程详解(一)的相关教程结束。

《UBOOT编译--- make xxx_deconfig过程详解(一).doc》

下载本文的Word格式文档，以方便收藏与打印。

Copyright 2023. 昆居客 - IT编程,互联网信息技术文档大全!